diff --git a/arch/powerpc/cpu/mpc8260/Kconfig b/arch/powerpc/cpu/mpc8260/Kconfig
index eab4514..55941c8 100644
--- a/arch/powerpc/cpu/mpc8260/Kconfig
+++ b/arch/powerpc/cpu/mpc8260/Kconfig
@@ -7,15 +7,11 @@
 choice
 	prompt "Target select"
 
-config TARGET_ATC
-	bool "Support atc"
-
 config TARGET_KM82XX
 	bool "Support km82xx"
 
 endchoice
 
-source "board/atc/Kconfig"
 source "board/keymile/km82xx/Kconfig"
 
 endmenu
diff --git a/board/atc/Kconfig b/board/atc/Kconfig
deleted file mode 100644
index 9b336ca..0000000
--- a/board/atc/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_ATC
-
-config SYS_BOARD
-	default "atc"
-
-config SYS_CONFIG_NAME
-	default "atc"
-
-endif
diff --git a/board/atc/MAINTAINERS b/board/atc/MAINTAINERS
deleted file mode 100644
index 1c5d61e..0000000
--- a/board/atc/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-ATC BOARD
-M:	Wolfgang Denk <wd@denx.de>
-S:	Maintained
-F:	board/atc/
-F:	include/configs/atc.h
-F:	configs/atc_defconfig
diff --git a/board/atc/Makefile b/board/atc/Makefile
deleted file mode 100644
index 3a163c4..0000000
--- a/board/atc/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	= atc.o flash.o ti113x.o
diff --git a/board/atc/atc.c b/board/atc/atc.c
deleted file mode 100644
index 0038561..0000000
--- a/board/atc/atc.c
+++ /dev/null
@@ -1,382 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <ioports.h>
-#include <mpc8260.h>
-#include <pci.h>
-
-/*
- * I/O Port configuration table
- *
- * if conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- */
-
-const iop_conf_t iop_conf_tab[4][32] = {
-
-    /* Port A configuration */
-    {	/*	      conf ppar psor pdir podr pdat */
-	/* PA31 */ {   1,   1,   1,   0,   0,   0   }, /* FCC1 MII COL */
-	/* PA30 */ {   1,   1,   1,   0,   0,   0   }, /* FCC1 MII CRS */
-	/* PA29 */ {   1,   1,   1,   1,   0,   0   }, /* FCC1 MII TX_ER */
-	/* PA28 */ {   1,   1,   1,   1,   0,   0   }, /* FCC1 MII TX_EN */
-	/* PA27 */ {   1,   1,   1,   0,   0,   0   }, /* FCC1 MII RX_DV */
-	/* PA26 */ {   1,   1,   1,   0,   0,   0   }, /* FCC1 MII RX_ER */
-	/* PA25 */ {   1,   0,   0,   1,   0,   0   }, /* FCC2 MII MDIO */
-	/* PA24 */ {   1,   0,   0,   1,   0,   0   }, /* FCC2 MII MDC */
-	/* PA23 */ {   1,   0,   0,   1,   0,   0   }, /* FCC1 MII MDIO */
-	/* PA22 */ {   1,   0,   0,   1,   0,   0   }, /* FCC1 MII MDC */
-	/* PA21 */ {   1,   1,   0,   1,   0,   0   }, /* FCC1 MII TxD[3] */
-	/* PA20 */ {   1,   1,   0,   1,   0,   0   }, /* FCC1 MII TxD[2] */
-	/* PA19 */ {   1,   1,   0,   1,   0,   0   }, /* FCC1 MII TxD[1] */
-	/* PA18 */ {   1,   1,   0,   1,   0,   0   }, /* FCC1 MII TxD[0] */
-	/* PA17 */ {   1,   1,   0,   0,   0,   0   }, /* FCC1 MII RxD[0] */
-	/* PA16 */ {   1,   1,   0,   0,   0,   0   }, /* FCC1 MII RxD[1] */
-	/* PA15 */ {   1,   1,   0,   0,   0,   0   }, /* FCC1 MII RxD[2] */
-	/* PA14 */ {   1,   1,   0,   0,   0,   0   }, /* FCC1 MII RxD[3] */
-	/* PA13 */ {   1,   0,   0,   1,   0,   0   }, /* FCC2 MII TXSL1 */
-	/* PA12 */ {   1,   0,   0,   1,   0,   1   }, /* FCC2 MII TXSL0 */
-	/* PA11 */ {   1,   0,   0,   1,   0,   0   }, /* FCC1 MII TXSL1 */
-	/* PA10 */ {   1,   0,   0,   1,   0,   1   }, /* FCC1 MII TXSL0 */
-#if 1
-	/* PA9  */ {   0,   1,   0,   1,   0,   0   }, /* SMC2 TXD */
-	/* PA8  */ {   0,   1,   0,   0,   0,   0   }, /* SMC2 RXD */
-#else
-	/* PA9  */ {   1,   1,   0,   1,   0,   0   }, /* SMC2 TXD */
-	/* PA8  */ {   1,   1,   0,   0,   0,   0   }, /* SMC2 RXD */
-#endif
-	/* PA7  */ {   0,   0,   0,   0,   0,   0   }, /* PA7 */
-	/* PA6  */ {   1,   0,   0,   1,   0,   1   }, /* FCC2 MII PAUSE */
-	/* PA5  */ {   1,   0,   0,   1,   0,   1   }, /* FCC1 MII PAUSE */
-	/* PA4  */ {   1,   0,   0,   1,   0,   0   }, /* FCC2 MII PWRDN */
-	/* PA3  */ {   1,   0,   0,   1,   0,   0   }, /* FCC1 MII PWRDN */
-	/* PA2  */ {   0,   0,   0,   0,   0,   0   }, /* PA2 */
-	/* PA1  */ {   1,   0,   0,   0,   0,   0   }, /* FCC2 MII MDINT */
-	/* PA0  */ {   1,   0,   0,   1,   0,   0   }  /* FCC1 MII MDINT */
-    },
-
-    /* Port B configuration */
-    {   /*	      conf ppar psor pdir podr pdat */
-	/* PB31 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TX_ER */
-	/* PB30 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_DV */
-	/* PB29 */ {   1,   1,   1,   1,   0,   0   }, /* FCC2 MII TX_EN */
-	/* PB28 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_ER */
-	/* PB27 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII COL */
-	/* PB26 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII CRS */
-	/* PB25 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[3] */
-	/* PB24 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[2] */
-	/* PB23 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[1] */
-	/* PB22 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[0] */
-	/* PB21 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[0] */
-	/* PB20 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[1] */
-	/* PB19 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[2] */
-	/* PB18 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[3] */
-	/* PB17 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3 MII RX_DV */
-	/* PB16 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3 MII RX_ER */
-	/* PB15 */ {   1,   1,   0,   1,   0,   0   }, /* FCC3 MII TX_ER */
-	/* PB14 */ {   1,   1,   0,   1,   0,   0   }, /* FCC3 MII TX_EN */
-	/* PB13 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3 MII COL */
-	/* PB12 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3 MII CRS */
-	/* PB11 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3 MII RxD */
-	/* PB10 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3 MII RxD */
-	/* PB9  */ {   1,   1,   0,   0,   0,   0   }, /* FCC3 MII RxD */
-	/* PB8  */ {   1,   1,   0,   0,   0,   0   }, /* FCC3 MII RxD */
-	/* PB7  */ {   1,   1,   0,   1,   0,   0   }, /* FCC3 MII TxD */
-	/* PB6  */ {   1,   1,   0,   1,   0,   0   }, /* FCC3 MII TxD */
-	/* PB5  */ {   1,   1,   0,   1,   0,   0   }, /* FCC3 MII TxD */
-	/* PB4  */ {   1,   1,   0,   1,   0,   0   }, /* FCC3 MII TxD */
-	/* PB3  */ {   0,   0,   0,   0,   0,   0   }, /* PB3 */
-	/* PB2  */ {   0,   0,   0,   0,   0,   0   }, /* PB2 */
-	/* PB1  */ {   0,   0,   0,   0,   0,   0   }, /* PB1 */
-	/* PB0  */ {   0,   0,   0,   0,   0,   0   }  /* PB0 */
-    },
-
-    /* Port C */
-    {   /*	      conf ppar psor pdir podr pdat */
-	/* PC31 */ {   0,   0,   0,   0,   0,   0   }, /* PC31 */
-	/* PC30 */ {   0,   0,   0,   0,   0,   0   }, /* PC30 */
-	/* PC29 */ {   1,   0,   0,   0,   0,   0   }, /* SCC1 CTS */
-	/* PC28 */ {   1,   0,   0,   0,   0,   0   }, /* SCC2 CTS */
-	/* PC27 */ {   0,   0,   0,   0,   0,   0   }, /* PC27 */
-	/* PC26 */ {   0,   0,   0,   0,   0,   0   }, /* PC26 */
-	/* PC25 */ {   0,   0,   0,   0,   0,   0   }, /* PC25 */
-	/* PC24 */ {   0,   0,   0,   0,   0,   0   }, /* PC24 */
-	/* PC23 */ {   0,   0,   0,   0,   0,   0   }, /* FDC37C78 DACFD */
-	/* PC22 */ {   0,   0,   0,   0,   0,   0   }, /* FDC37C78 DNFD */
-	/* PC21 */ {   1,   1,   0,   0,   0,   0   }, /* FCC1 MII RX_CLK */
-	/* PC20 */ {   1,   1,   0,   0,   0,   0   }, /* FCC1 MII TX_CLK */
-	/* PC19 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_CLK */
-	/* PC18 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII TX_CLK */
-	/* PC17 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3 MII RX_CLK */
-	/* PC16 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3 MII TX_CLK */
-#if 0
-	/* PC15 */ {   0,   0,   0,   0,   0,   0   }, /* PC15 */
-#else
-	/* PC15 */ {   1,   1,   0,   1,   0,   0   }, /* PC15 */
-#endif
-	/* PC14 */ {   0,   0,   0,   0,   0,   0   }, /* PC14 */
-	/* PC13 */ {   0,   0,   0,   0,   0,   0   }, /* PC13 */
-	/* PC12 */ {   0,   0,   0,   0,   0,   0   }, /* PC12 */
-	/* PC11 */ {   0,   0,   0,   0,   0,   0   }, /* PC11 */
-	/* PC10 */ {   0,   0,   0,   0,   0,   0   }, /* PC10 */
-	/* PC9  */ {   0,   0,   0,   0,   0,   0   }, /* FC9 */
-	/* PC8  */ {   0,   0,   0,   0,   0,   0   }, /* PC8 */
-	/* PC7  */ {   0,   0,   0,   0,   0,   0   }, /* PC7 */
-	/* PC6  */ {   0,   0,   0,   0,   0,   0   }, /* PC6 */
-	/* PC5  */ {   0,   0,   0,   0,   0,   0   }, /* PC5 */
-	/* PC4  */ {   0,   0,   0,   0,   0,   0   }, /* PC4 */
-	/* PC3  */ {   0,   0,   0,   0,   0,   0   }, /* PC3 */
-	/* PC2  */ {   0,   0,   0,   0,   0,   0   }, /* PC2 */
-	/* PC1  */ {   0,   0,   0,   0,   0,   0   }, /* PC1 */
-	/* PC0  */ {   0,   0,   0,   0,   0,   0   }, /* FDC37C78 DRQFD */
-    },
-
-    /* Port D */
-    {   /*	      conf ppar psor pdir podr pdat */
-	/* PD31 */ {   1,   1,   0,   0,   0,   0   }, /* SCC1 RXD */
-	/* PD30 */ {   1,   1,   1,   1,   0,   0   }, /* SCC1 TXD */
-	/* PD29 */ {   1,   0,   0,   1,   0,   0   }, /* SCC1 RTS */
-	/* PD28 */ {   1,   1,   0,   0,   0,   0   }, /* SCC2 RXD */
-	/* PD27 */ {   1,   1,   0,   1,   0,   0   }, /* SCC2 TXD */
-	/* PD26 */ {   1,   0,   0,   1,   0,   0   }, /* SCC2 RTS */
-	/* PD25 */ {   0,   0,   0,   0,   0,   0   }, /* PD25 */
-	/* PD24 */ {   0,   0,   0,   0,   0,   0   }, /* PD24 */
-	/* PD23 */ {   0,   0,   0,   0,   0,   0   }, /* PD23 */
-	/* PD22 */ {   0,   0,   0,   0,   0,   0   }, /* PD22 */
-	/* PD21 */ {   0,   0,   0,   0,   0,   0   }, /* PD21 */
-	/* PD20 */ {   0,   0,   0,   0,   0,   0   }, /* PD20 */
-	/* PD19 */ {   0,   0,   0,   0,   0,   0   }, /* PD19 */
-	/* PD18 */ {   0,   0,   0,   0,   0,   0   }, /* PD18 */
-	/* PD17 */ {   0,   0,   0,   0,   0,   0   }, /* PD17 */
-	/* PD16 */ {   0,   0,   0,   0,   0,   0   }, /* PD16 */
-#if defined(CONFIG_SYS_I2C_SOFT)
-	/* PD15 */ {   1,   0,   0,   1,   1,   1   }, /* I2C SDA */
-	/* PD14 */ {   1,   0,   0,   1,   1,   1   }, /* I2C SCL */
-#else
-#if defined(CONFIG_HARD_I2C)
-	/* PD15 */ {   1,   1,   1,   0,   1,   0   }, /* I2C SDA */
-	/* PD14 */ {   1,   1,   1,   0,   1,   0   }, /* I2C SCL */
-#else /* normal I/O port pins */
-	/* PD15 */ {   1,   1,   1,   0,   1,   0   }, /* I2C SDA */
-	/* PD14 */ {   1,   1,   1,   0,   1,   0   }, /* I2C SCL */
-#endif
-#endif
-	/* PD13 */ {   0,   0,   0,   0,   0,   0   }, /* PD13 */
-	/* PD12 */ {   0,   0,   0,   0,   0,   0   }, /* PD12 */
-	/* PD11 */ {   0,   0,   0,   0,   0,   0   }, /* PD11 */
-	/* PD10 */ {   0,   0,   0,   0,   0,   0   }, /* PD10 */
-	/* PD9  */ {   1,   1,   0,   1,   0,   0   }, /* SMC1 TXD */
-	/* PD8  */ {   1,   1,   0,   0,   0,   0   }, /* SMC1 RXD */
-	/* PD7  */ {   0,   0,   0,   0,   0,   0   }, /* PD7 */
-	/* PD6  */ {   0,   0,   0,   0,   0,   0   }, /* PD6 */
-	/* PD5  */ {   0,   0,   0,   0,   0,   0   }, /* PD5 */
-#if 0
-	/* PD4  */ {   0,   0,   0,   0,   0,   0   }, /* PD4 */
-#else
-	/* PD4  */ {   1,   1,   1,   0,   0,   0   }, /* PD4 */
-#endif
-	/* PD3  */ {   0,   0,   0,   0,   0,   0   }, /* PD3 */
-	/* PD2  */ {   0,   0,   0,   0,   0,   0   }, /* PD2 */
-	/* PD1  */ {   0,   0,   0,   0,   0,   0   }, /* PD1 */
-	/* PD0  */ {   0,   0,   0,   0,   0,   0   }  /* PD0 */
-    }
-};
-
-/*
- * UPMB initialization table
- */
-#define	_NOT_USED_	0xFFFFFFFF
-
-static const uint rtc_table[] =
-{
-	/*
-	 * Single Read. (Offset 0 in UPMA RAM)
-	 */
-	0xfffec00, 0xfffac00, 0xfff2d00, 0xfef2800,
-	0xfaf2080, 0xfaf2080, 0xfff2400, 0x1fff6c05, /* last */
-	/*
-	 * Burst Read. (Offset 8 in UPMA RAM)
-	 */
-	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
-	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
-	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
-	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
-	/*
-	 * Single Write. (Offset 18 in UPMA RAM)
-	 */
-	0xfffec00, 0xfffac00, 0xfff2d00, 0xfef2800,
-	0xfaf2080, 0xfaf2080, 0xfaf2400, 0x1fbf6c05, /* last */
-	/*
-	 * Burst Write. (Offset 20 in UPMA RAM)
-	 */
-	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
-	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
-	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
-	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
-	/*
-	 * Refresh  (Offset 30 in UPMA RAM)
-	 */
-	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
-	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
-	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
-	/*
-	 * Exception. (Offset 3c in UPMA RAM)
-	 */
-	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
-};
-
-/* ------------------------------------------------------------------------- */
-
-/* Check Board Identity:
- */
-int checkboard (void)
-{
-	printf ("Board: ATC\n");
-	return 0;
-}
-
-/* ------------------------------------------------------------------------- */
-
-/* Try SDRAM initialization with P/LSDMR=sdmr and ORx=orx
- *
- * This routine performs standard 8260 initialization sequence
- * and calculates the available memory size. It may be called
- * several times to try different SDRAM configurations on both
- * 60x and local buses.
- */
-static long int try_init (volatile memctl8260_t * memctl, ulong sdmr,
-			  ulong orx, volatile uchar * base)
-{
-	volatile uchar c = 0xff;
-	volatile uint *sdmr_ptr;
-	volatile uint *orx_ptr;
-	ulong maxsize, size;
-	int i;
-
-	/* We must be able to test a location outsize the maximum legal size
-	 * to find out THAT we are outside; but this address still has to be
-	 * mapped by the controller. That means, that the initial mapping has
-	 * to be (at least) twice as large as the maximum expected size.
-	 */
-	maxsize = (1 + (~orx | 0x7fff)) / 2;
-
-	/* Since CONFIG_SYS_SDRAM_BASE is always 0 (??), we assume that
-	 * we are configuring CS1 if base != 0
-	 */
-	sdmr_ptr = &memctl->memc_psdmr;
-	orx_ptr = &memctl->memc_or2;
-
-	*orx_ptr = orx;
-
-	/*
-	 * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35):
-	 *
-	 * "At system reset, initialization software must set up the
-	 *  programmable parameters in the memory controller banks registers
-	 *  (ORx, BRx, P/LSDMR). After all memory parameters are configured,
-	 *  system software should execute the following initialization sequence
-	 *  for each SDRAM device.
-	 *
-	 *  1. Issue a PRECHARGE-ALL-BANKS command
-	 *  2. Issue eight CBR REFRESH commands
-	 *  3. Issue a MODE-SET command to initialize the mode register
-	 *
-	 *  The initial commands are executed by setting P/LSDMR[OP] and
-	 *  accessing the SDRAM with a single-byte transaction."
-	 *
-	 * The appropriate BRx/ORx registers have already been set when we
-	 * get here. The SDRAM can be accessed at the address CONFIG_SYS_SDRAM_BASE.
-	 */
-
-	*sdmr_ptr = sdmr | PSDMR_OP_PREA;
-	*base = c;
-
-	*sdmr_ptr = sdmr | PSDMR_OP_CBRR;
-	for (i = 0; i < 8; i++)
-		*base = c;
-
-	*sdmr_ptr = sdmr | PSDMR_OP_MRW;
-	*(base + CONFIG_SYS_MRS_OFFS) = c;	/* setting MR on address lines */
-
-	*sdmr_ptr = sdmr | PSDMR_OP_NORM | PSDMR_RFEN;
-	*base = c;
-
-	size = get_ram_size((long *)base, maxsize);
-
-	*orx_ptr = orx | ~(size - 1);
-
-	return (size);
-}
-
-int misc_init_r(void)
-{
-	volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-	volatile memctl8260_t *memctl = &immap->im_memctl;
-
-	upmconfig(UPMA, (uint *)rtc_table, sizeof(rtc_table) / sizeof(uint));
-	memctl->memc_mamr = MxMR_RLFx_6X | MxMR_WLFx_6X | MxMR_OP_NORM;
-
-	return (0);
-}
-
-phys_size_t initdram (int board_type)
-{
-	volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-	volatile memctl8260_t *memctl = &immap->im_memctl;
-
-#ifndef CONFIG_SYS_RAMBOOT
-	ulong size8, size9;
-#endif
-	long psize;
-
-	psize = 8 * 1024 * 1024;
-
-	memctl->memc_mptpr = CONFIG_SYS_MPTPR;
-	memctl->memc_psrt = CONFIG_SYS_PSRT;
-
-#ifndef CONFIG_SYS_RAMBOOT
-	/* 60x SDRAM setup:
-	 */
-	size8 = try_init (memctl, CONFIG_SYS_PSDMR_8COL, CONFIG_SYS_OR2_8COL,
-			  (uchar *) CONFIG_SYS_SDRAM_BASE);
-	size9 = try_init (memctl, CONFIG_SYS_PSDMR_9COL, CONFIG_SYS_OR2_9COL,
-			  (uchar *) CONFIG_SYS_SDRAM_BASE);
-
-	if (size8 < size9) {
-		psize = size9;
-		printf ("(60x:9COL) ");
-	} else {
-		psize = try_init (memctl, CONFIG_SYS_PSDMR_8COL, CONFIG_SYS_OR2_8COL,
-				  (uchar *) CONFIG_SYS_SDRAM_BASE);
-		printf ("(60x:8COL) ");
-	}
-
-#endif	/* CONFIG_SYS_RAMBOOT */
-
-	icache_enable ();
-
-	return (psize);
-}
-
-#if defined(CONFIG_CMD_DOC)
-void doc_init (void)
-{
-	doc_probe (CONFIG_SYS_DOC_BASE);
-}
-#endif
-
-#ifdef	CONFIG_PCI
-struct pci_controller hose;
-
-extern void pci_mpc8250_init(struct pci_controller *);
-
-void pci_init_board(void)
-{
-	pci_mpc8250_init(&hose);
-}
-#endif
diff --git a/board/atc/flash.c b/board/atc/flash.c
deleted file mode 100644
index 5a9c510..0000000
--- a/board/atc/flash.c
+++ /dev/null
@@ -1,647 +0,0 @@
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-
-flash_info_t	flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
-
-/* NOTE - CONFIG_FLASH_16BIT means the CPU interface is 16-bit, it
- *        has nothing to do with the flash chip being 8-bit or 16-bit.
- */
-#ifdef CONFIG_FLASH_16BIT
-typedef unsigned short FLASH_PORT_WIDTH;
-typedef volatile unsigned short FLASH_PORT_WIDTHV;
-#define	FLASH_ID_MASK	0xFFFF
-#else
-typedef unsigned long FLASH_PORT_WIDTH;
-typedef volatile unsigned long FLASH_PORT_WIDTHV;
-#define	FLASH_ID_MASK	0xFFFFFFFF
-#endif
-
-#define FPW	FLASH_PORT_WIDTH
-#define FPWV	FLASH_PORT_WIDTHV
-
-#define ORMASK(size) ((-size) & OR_AM_MSK)
-
-#define FLASH_CYCLE1	0x0555
-#define FLASH_CYCLE2	0x02aa
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size(FPWV *addr, flash_info_t *info);
-static void flash_reset(flash_info_t *info);
-static int write_word_intel(flash_info_t *info, FPWV *dest, FPW data);
-static int write_word_amd(flash_info_t *info, FPWV *dest, FPW data);
-static void flash_get_offsets(ulong base, flash_info_t *info);
-static flash_info_t *flash_get_info(ulong base);
-
-/*-----------------------------------------------------------------------
- * flash_init()
- *
- * sets up flash_info and returns size of FLASH (bytes)
- */
-unsigned long flash_init (void)
-{
-	unsigned long size = 0;
-	int i;
-
-	/* Init: no FLASHes known */
-	for (i=0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
-#if 0
-		ulong flashbase = (i == 0) ? PHYS_FLASH_1 : PHYS_FLASH_2;
-#else
-		ulong flashbase = CONFIG_SYS_FLASH_BASE;
-#endif
-
-		memset(&flash_info[i], 0, sizeof(flash_info_t));
-
-		flash_info[i].size =
-			flash_get_size((FPW *)flashbase, &flash_info[i]);
-
-		if (flash_info[i].flash_id == FLASH_UNKNOWN) {
-			printf ("## Unknown FLASH on Bank %d - Size = 0x%08lx\n",
-			i, flash_info[i].size);
-		}
-
-		size += flash_info[i].size;
-	}
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
-	/* monitor protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CONFIG_SYS_MONITOR_BASE,
-		      CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1,
-		      flash_get_info(CONFIG_SYS_MONITOR_BASE));
-#endif
-
-#ifdef	CONFIG_ENV_IS_IN_FLASH
-	/* ENV protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CONFIG_ENV_ADDR,
-		      CONFIG_ENV_ADDR+CONFIG_ENV_SIZE-1,
-		      flash_get_info(CONFIG_ENV_ADDR));
-#endif
-
-
-	return size ? size : 1;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_reset(flash_info_t *info)
-{
-	FPWV *base = (FPWV *)(info->start[0]);
-
-	/* Put FLASH back in read mode */
-	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL)
-		*base = (FPW)0x00FF00FF;	/* Intel Read Mode */
-	else if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_AMD)
-		*base = (FPW)0x00F000F0;	/* AMD Read Mode */
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t *info)
-{
-	int i;
-
-	/* set up sector start address table */
-	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL
-	    && (info->flash_id & FLASH_BTYPE)) {
-		int bootsect_size;	/* number of bytes/boot sector	*/
-		int sect_size;		/* number of bytes/regular sector */
-
-		bootsect_size = 0x00002000 * (sizeof(FPW)/2);
-		sect_size =     0x00010000 * (sizeof(FPW)/2);
-
-		/* set sector offsets for bottom boot block type	*/
-		for (i = 0; i < 8; ++i) {
-			info->start[i] = base + (i * bootsect_size);
-		}
-		for (i = 8; i < info->sector_count; i++) {
-			info->start[i] = base + ((i - 7) * sect_size);
-		}
-	}
-	else if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_AMD
-		 && (info->flash_id & FLASH_TYPEMASK) == FLASH_AM640U) {
-
-		int sect_size;		/* number of bytes/sector */
-
-		sect_size = 0x00010000 * (sizeof(FPW)/2);
-
-		/* set up sector start address table (uniform sector type) */
-		for( i = 0; i < info->sector_count; i++ )
-			info->start[i] = base + (i * sect_size);
-	}
-}
-
-/*-----------------------------------------------------------------------
- */
-
-static flash_info_t *flash_get_info(ulong base)
-{
-	int i;
-	flash_info_t * info;
-
-	for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i ++) {
-		info = & flash_info[i];
-		if (info->start[0] <= base && base < info->start[0] + info->size)
-			break;
-	}
-
-	return i == CONFIG_SYS_MAX_FLASH_BANKS ? 0 : info;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-void flash_print_info (flash_info_t *info)
-{
-	int i;
-	uchar *boottype;
-	uchar *bootletter;
-	char *fmt;
-	uchar botbootletter[] = "B";
-	uchar topbootletter[] = "T";
-	uchar botboottype[] = "bottom boot sector";
-	uchar topboottype[] = "top boot sector";
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_AMD:	printf ("AMD ");		break;
-	case FLASH_MAN_BM:	printf ("BRIGHT MICRO ");	break;
-	case FLASH_MAN_FUJ:	printf ("FUJITSU ");		break;
-	case FLASH_MAN_SST:	printf ("SST ");		break;
-	case FLASH_MAN_STM:	printf ("STM ");		break;
-	case FLASH_MAN_INTEL:	printf ("INTEL ");		break;
-	default:		printf ("Unknown Vendor ");	break;
-	}
-
-	/* check for top or bottom boot, if it applies */
-	if (info->flash_id & FLASH_BTYPE) {
-		boottype = botboottype;
-		bootletter = botbootletter;
-	}
-	else {
-		boottype = topboottype;
-		bootletter = topbootletter;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_AM640U:
-		fmt = "29LV641D (64 Mbit, uniform sectors)\n";
-		break;
-	case FLASH_28F800C3B:
-	case FLASH_28F800C3T:
-		fmt = "28F800C3%s (8 Mbit, %s)\n";
-		break;
-	case FLASH_INTEL800B:
-	case FLASH_INTEL800T:
-		fmt = "28F800B3%s (8 Mbit, %s)\n";
-		break;
-	case FLASH_28F160C3B:
-	case FLASH_28F160C3T:
-		fmt = "28F160C3%s (16 Mbit, %s)\n";
-		break;
-	case FLASH_INTEL160B:
-	case FLASH_INTEL160T:
-		fmt = "28F160B3%s (16 Mbit, %s)\n";
-		break;
-	case FLASH_28F320C3B:
-	case FLASH_28F320C3T:
-		fmt = "28F320C3%s (32 Mbit, %s)\n";
-		break;
-	case FLASH_INTEL320B:
-	case FLASH_INTEL320T:
-		fmt = "28F320B3%s (32 Mbit, %s)\n";
-		break;
-	case FLASH_28F640C3B:
-	case FLASH_28F640C3T:
-		fmt = "28F640C3%s (64 Mbit, %s)\n";
-		break;
-	case FLASH_INTEL640B:
-	case FLASH_INTEL640T:
-		fmt = "28F640B3%s (64 Mbit, %s)\n";
-		break;
-	default:
-		fmt = "Unknown Chip Type\n";
-		break;
-	}
-
-	printf (fmt, bootletter, boottype);
-
-	printf ("  Size: %ld MB in %d Sectors\n",
-		info->size >> 20,
-		info->sector_count);
-
-	printf ("  Sector Start Addresses:");
-
-	for (i=0; i<info->sector_count; ++i) {
-		if ((i % 5) == 0) {
-			printf ("\n   ");
-		}
-
-		printf (" %08lX%s", info->start[i],
-			info->protect[i] ? " (RO)" : "     ");
-	}
-
-	printf ("\n");
-}
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-ulong flash_get_size (FPWV *addr, flash_info_t *info)
-{
-	/* Write auto select command: read Manufacturer ID */
-
-	/* Write auto select command sequence and test FLASH answer */
-	addr[FLASH_CYCLE1] = (FPW)0x00AA00AA;	/* for AMD, Intel ignores this */
-	addr[FLASH_CYCLE2] = (FPW)0x00550055;	/* for AMD, Intel ignores this */
-	addr[FLASH_CYCLE1] = (FPW)0x00900090;	/* selects Intel or AMD */
-
-	/* The manufacturer codes are only 1 byte, so just use 1 byte.
-	 * This works for any bus width and any FLASH device width.
-	 */
-	udelay(100);
-	switch (addr[0] & 0xff) {
-
-	case (uchar)AMD_MANUFACT:
-		info->flash_id = FLASH_MAN_AMD;
-		break;
-
-	case (uchar)INTEL_MANUFACT:
-		info->flash_id = FLASH_MAN_INTEL;
-		break;
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		break;
-	}
-
-	/* Check 16 bits or 32 bits of ID so work on 32 or 16 bit bus. */
-	if (info->flash_id != FLASH_UNKNOWN) switch (addr[1]) {
-
-	case (FPW)AMD_ID_LV640U:	/* 29LV640 and 29LV641 have same ID */
-		info->flash_id += FLASH_AM640U;
-		info->sector_count = 128;
-		info->size = 0x00800000 * (sizeof(FPW)/2);
-		break;				/* => 8 or 16 MB	*/
-
-	case (FPW)INTEL_ID_28F800C3B:
-		info->flash_id += FLASH_28F800C3B;
-		info->sector_count = 23;
-		info->size = 0x00100000 * (sizeof(FPW)/2);
-		break;				/* => 1 or 2 MB		*/
-
-	case (FPW)INTEL_ID_28F800B3B:
-		info->flash_id += FLASH_INTEL800B;
-		info->sector_count = 23;
-		info->size = 0x00100000 * (sizeof(FPW)/2);
-		break;				/* => 1 or 2 MB		*/
-
-	case (FPW)INTEL_ID_28F160C3B:
-		info->flash_id += FLASH_28F160C3B;
-		info->sector_count = 39;
-		info->size = 0x00200000 * (sizeof(FPW)/2);
-		break;				/* => 2 or 4 MB		*/
-
-	case (FPW)INTEL_ID_28F160B3B:
-		info->flash_id += FLASH_INTEL160B;
-		info->sector_count = 39;
-		info->size = 0x00200000 * (sizeof(FPW)/2);
-		break;				/* => 2 or 4 MB		*/
-
-	case (FPW)INTEL_ID_28F320C3B:
-		info->flash_id += FLASH_28F320C3B;
-		info->sector_count = 71;
-		info->size = 0x00400000 * (sizeof(FPW)/2);
-		break;				/* => 4 or 8 MB		*/
-
-	case (FPW)INTEL_ID_28F320B3B:
-		info->flash_id += FLASH_INTEL320B;
-		info->sector_count = 71;
-		info->size = 0x00400000 * (sizeof(FPW)/2);
-		break;				/* => 4 or 8 MB		*/
-
-	case (FPW)INTEL_ID_28F640C3B:
-		info->flash_id += FLASH_28F640C3B;
-		info->sector_count = 135;
-		info->size = 0x00800000 * (sizeof(FPW)/2);
-		break;				/* => 8 or 16 MB	*/
-
-	case (FPW)INTEL_ID_28F640B3B:
-		info->flash_id += FLASH_INTEL640B;
-		info->sector_count = 135;
-		info->size = 0x00800000 * (sizeof(FPW)/2);
-		break;				/* => 8 or 16 MB	*/
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		return (0);			/* => no or unknown flash */
-	}
-
-	flash_get_offsets((ulong)addr, info);
-
-	/* Put FLASH back in read mode */
-	flash_reset(info);
-
-	return (info->size);
-}
-
-/*-----------------------------------------------------------------------
- */
-
-int	flash_erase (flash_info_t *info, int s_first, int s_last)
-{
-	FPWV *addr;
-	int flag, prot, sect;
-	int intel = (info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL;
-	ulong start, now, last;
-	int rcode = 0;
-
-	if ((s_first < 0) || (s_first > s_last)) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf ("- missing\n");
-		} else {
-			printf ("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_INTEL800B:
-	case FLASH_INTEL160B:
-	case FLASH_INTEL320B:
-	case FLASH_INTEL640B:
-	case FLASH_28F800C3B:
-	case FLASH_28F160C3B:
-	case FLASH_28F320C3B:
-	case FLASH_28F640C3B:
-	case FLASH_AM640U:
-		break;
-	case FLASH_UNKNOWN:
-	default:
-		printf ("Can't erase unknown flash type %08lx - aborted\n",
-			info->flash_id);
-		return 1;
-	}
-
-	prot = 0;
-	for (sect=s_first; sect<=s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-			prot);
-	} else {
-		printf ("\n");
-	}
-
-	last  = get_timer(0);
-
-	/* Start erase on unprotected sectors */
-	for (sect = s_first; sect<=s_last && rcode == 0; sect++) {
-
-		if (info->protect[sect] != 0)	/* protected, skip it */
-			continue;
-
-		/* Disable interrupts which might cause a timeout here */
-		flag = disable_interrupts();
-
-		addr = (FPWV *)(info->start[sect]);
-		if (intel) {
-			*addr = (FPW)0x00500050; /* clear status register */
-			*addr = (FPW)0x00200020; /* erase setup */
-			*addr = (FPW)0x00D000D0; /* erase confirm */
-		}
-		else {
-			/* must be AMD style if not Intel */
-			FPWV *base;		/* first address in bank */
-
-			base = (FPWV *)(info->start[0]);
-			base[FLASH_CYCLE1] = (FPW)0x00AA00AA;	/* unlock */
-			base[FLASH_CYCLE2] = (FPW)0x00550055;	/* unlock */
-			base[FLASH_CYCLE1] = (FPW)0x00800080;	/* erase mode */
-			base[FLASH_CYCLE1] = (FPW)0x00AA00AA;	/* unlock */
-			base[FLASH_CYCLE2] = (FPW)0x00550055;	/* unlock */
-			*addr = (FPW)0x00300030;	/* erase sector */
-		}
-
-		/* re-enable interrupts if necessary */
-		if (flag)
-			enable_interrupts();
-
-		start = get_timer(0);
-
-		/* wait at least 50us for AMD, 80us for Intel.
-		 * Let's wait 1 ms.
-		 */
-		udelay (1000);
-
-		while ((*addr & (FPW)0x00800080) != (FPW)0x00800080) {
-			if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
-				printf ("Timeout\n");
-
-				if (intel) {
-					/* suspend erase	*/
-					*addr = (FPW)0x00B000B0;
-				}
-
-				flash_reset(info);	/* reset to read mode */
-				rcode = 1;		/* failed */
-				break;
-			}
-
-			/* show that we're waiting */
-			if ((get_timer(last)) > CONFIG_SYS_HZ) {/* every second */
-				putc ('.');
-				last = get_timer(0);
-			}
-		}
-
-		/* show that we're waiting */
-		if ((get_timer(last)) > CONFIG_SYS_HZ) {	/* every second */
-			putc ('.');
-			last = get_timer(0);
-		}
-
-		flash_reset(info);	/* reset to read mode	*/
-	}
-
-	printf (" done\n");
-	return rcode;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
-	FPW data = 0; /* 16 or 32 bit word, matches flash bus width on MPC8XX */
-	int bytes;	  /* number of bytes to program in current word		*/
-	int left;	  /* number of bytes left to program			*/
-	int i, res;
-
-	for (left = cnt, res = 0;
-		 left > 0 && res == 0;
-		 addr += sizeof(data), left -= sizeof(data) - bytes) {
-
-		bytes = addr & (sizeof(data) - 1);
-		addr &= ~(sizeof(data) - 1);
-
-		/* combine source and destination data so can program
-		 * an entire word of 16 or 32 bits
-		 */
-		for (i = 0; i < sizeof(data); i++) {
-			data <<= 8;
-			if (i < bytes || i - bytes >= left )
-				data += *((uchar *)addr + i);
-			else
-				data += *src++;
-		}
-
-		/* write one word to the flash */
-		switch (info->flash_id & FLASH_VENDMASK) {
-		case FLASH_MAN_AMD:
-			res = write_word_amd(info, (FPWV *)addr, data);
-			break;
-		case FLASH_MAN_INTEL:
-			res = write_word_intel(info, (FPWV *)addr, data);
-			break;
-		default:
-			/* unknown flash type, error! */
-			printf ("missing or unknown FLASH type\n");
-			res = 1;	/* not really a timeout, but gives error */
-			break;
-		}
-	}
-
-	return (res);
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash for AMD FLASH
- * A word is 16 or 32 bits, whichever the bus width of the flash bank
- * (not an individual chip) is.
- *
- * returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word_amd (flash_info_t *info, FPWV *dest, FPW data)
-{
-	ulong start;
-	int flag;
-	int res = 0;	/* result, assume success	*/
-	FPWV *base;		/* first address in flash bank	*/
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*dest & data) != data) {
-		return (2);
-	}
-
-
-	base = (FPWV *)(info->start[0]);
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	base[FLASH_CYCLE1] = (FPW)0x00AA00AA;	/* unlock */
-	base[FLASH_CYCLE2] = (FPW)0x00550055;	/* unlock */
-	base[FLASH_CYCLE1] = (FPW)0x00A000A0;	/* selects program mode */
-
-	*dest = data;		/* start programming the data	*/
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	start = get_timer (0);
-
-	/* data polling for D7 */
-	while (res == 0 && (*dest & (FPW)0x00800080) != (data & (FPW)0x00800080)) {
-		if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
-			*dest = (FPW)0x00F000F0;	/* reset bank */
-			res = 1;
-		}
-	}
-
-	return (res);
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash for Intel FLASH
- * A word is 16 or 32 bits, whichever the bus width of the flash bank
- * (not an individual chip) is.
- *
- * returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word_intel (flash_info_t *info, FPWV *dest, FPW data)
-{
-	ulong start;
-	int flag;
-	int res = 0;	/* result, assume success	*/
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*dest & data) != data) {
-		return (2);
-	}
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	*dest = (FPW)0x00500050;	/* clear status register	*/
-	*dest = (FPW)0x00FF00FF;	/* make sure in read mode	*/
-	*dest = (FPW)0x00400040;	/* program setup		*/
-
-	*dest = data;		/* start programming the data	*/
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	start = get_timer (0);
-
-	while (res == 0 && (*dest & (FPW)0x00800080) != (FPW)0x00800080) {
-		if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
-			*dest = (FPW)0x00B000B0;	/* Suspend program	*/
-			res = 1;
-		}
-	}
-
-	if (res == 0 && (*dest & (FPW)0x00100010))
-		res = 1;	/* write failed, time out error is close enough	*/
-
-	*dest = (FPW)0x00500050;	/* clear status register	*/
-	*dest = (FPW)0x00FF00FF;	/* make sure in read mode	*/
-
-	return (res);
-}
diff --git a/board/atc/ti113x.c b/board/atc/ti113x.c
deleted file mode 100644
index c7c502c..0000000
--- a/board/atc/ti113x.c
+++ /dev/null
@@ -1,620 +0,0 @@
-/*
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- ********************************************************************
- *
- * Lots of code copied from:
- *
- * i82365.c 1.352 - Linux driver for Intel 82365 and compatible
- * PC Card controllers, and Yenta-compatible PCI-to-CardBus controllers.
- * (C) 1999 David A. Hinds <dahinds@users.sourceforge.net>
- */
-
-#include <common.h>
-
-#ifdef CONFIG_I82365
-
-#include <command.h>
-#include <pci.h>
-#include <pcmcia.h>
-#include <asm/io.h>
-
-#include <pcmcia/ss.h>
-#include <pcmcia/i82365.h>
-#include <pcmcia/yenta.h>
-#include <pcmcia/ti113x.h>
-
-static struct pci_device_id supported[] = {
-	{PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_1510},
-	{0, 0}
-};
-
-#define CYCLE_TIME	120
-
-#ifdef DEBUG
-static void i82365_dump_regions (pci_dev_t dev);
-#endif
-
-typedef struct socket_info_t {
-	pci_dev_t	dev;
-	u_short		bcr;
-	u_char		pci_lat, cb_lat, sub_bus, cache;
-	u_int		cb_phys;
-
-	socket_cap_t	cap;
-	u_short		type;
-	u_int		flags;
-	ti113x_state_t	state;
-} socket_info_t;
-
-static socket_info_t socket;
-static socket_state_t state;
-static struct pccard_mem_map mem;
-static struct pccard_io_map io;
-
-/*====================================================================*/
-
-/* Some PCI shortcuts */
-
-static int pci_readb (socket_info_t * s, int r, u_char * v)
-{
-	return pci_read_config_byte (s->dev, r, v);
-}
-static int pci_writeb (socket_info_t * s, int r, u_char v)
-{
-	return pci_write_config_byte (s->dev, r, v);
-}
-static int pci_readw (socket_info_t * s, int r, u_short * v)
-{
-	return pci_read_config_word (s->dev, r, v);
-}
-static int pci_writew (socket_info_t * s, int r, u_short v)
-{
-	return pci_write_config_word (s->dev, r, v);
-}
-static int pci_readl (socket_info_t * s, int r, u_int * v)
-{
-	return pci_read_config_dword (s->dev, r, v);
-}
-static int pci_writel (socket_info_t * s, int r, u_int v)
-{
-	return pci_write_config_dword (s->dev, r, v);
-}
-
-/*====================================================================*/
-
-#define cb_readb(s, r)		readb((s)->cb_phys + (r))
-#define cb_readl(s, r)		readl((s)->cb_phys + (r))
-#define cb_writeb(s, r, v)	writeb(v, (s)->cb_phys + (r))
-#define cb_writel(s, r, v)	writel(v, (s)->cb_phys + (r))
-
-static u_char i365_get (socket_info_t * s, u_short reg)
-{
-	return cb_readb (s, 0x0800 + reg);
-}
-
-static void i365_set (socket_info_t * s, u_short reg, u_char data)
-{
-	cb_writeb (s, 0x0800 + reg, data);
-}
-
-static void i365_bset (socket_info_t * s, u_short reg, u_char mask)
-{
-	i365_set (s, reg, i365_get (s, reg) | mask);
-}
-
-static void i365_bclr (socket_info_t * s, u_short reg, u_char mask)
-{
-	i365_set (s, reg, i365_get (s, reg) & ~mask);
-}
-
-#if 0	/* not used */
-static void i365_bflip (socket_info_t * s, u_short reg, u_char mask, int b)
-{
-	u_char d = i365_get (s, reg);
-
-	i365_set (s, reg, (b) ? (d | mask) : (d & ~mask));
-}
-
-static u_short i365_get_pair (socket_info_t * s, u_short reg)
-{
-	return (i365_get (s, reg) + (i365_get (s, reg + 1) << 8));
-}
-#endif	/* not used */
-
-static void i365_set_pair (socket_info_t * s, u_short reg, u_short data)
-{
-	i365_set (s, reg, data & 0xff);
-	i365_set (s, reg + 1, data >> 8);
-}
-
-/*======================================================================
-
-    Code to save and restore global state information for TI 1130 and
-    TI 1131 controllers, and to set and report global configuration
-    options.
-
-======================================================================*/
-
-static void ti113x_get_state (socket_info_t * s)
-{
-	ti113x_state_t *p = &s->state;
-
-	pci_readl (s, TI113X_SYSTEM_CONTROL, &p->sysctl);
-	pci_readb (s, TI113X_CARD_CONTROL, &p->cardctl);
-	pci_readb (s, TI113X_DEVICE_CONTROL, &p->devctl);
-	pci_readb (s, TI1250_DIAGNOSTIC, &p->diag);
-	pci_readl (s, TI12XX_IRQMUX, &p->irqmux);
-}
-
-static void ti113x_set_state (socket_info_t * s)
-{
-	ti113x_state_t *p = &s->state;
-
-	pci_writel (s, TI113X_SYSTEM_CONTROL, p->sysctl);
-	pci_writeb (s, TI113X_CARD_CONTROL, p->cardctl);
-	pci_writeb (s, TI113X_DEVICE_CONTROL, p->devctl);
-	pci_writeb (s, TI1250_MULTIMEDIA_CTL, 0);
-	pci_writeb (s, TI1250_DIAGNOSTIC, p->diag);
-	pci_writel (s, TI12XX_IRQMUX, p->irqmux);
-	i365_set_pair (s, TI113X_IO_OFFSET (0), 0);
-	i365_set_pair (s, TI113X_IO_OFFSET (1), 0);
-}
-
-static u_int ti113x_set_opts (socket_info_t * s)
-{
-	ti113x_state_t *p = &s->state;
-	u_int mask = 0xffff;
-
-	p->cardctl &= ~TI113X_CCR_ZVENABLE;
-	p->cardctl |= TI113X_CCR_SPKROUTEN;
-
-	return mask;
-}
-
-/*======================================================================
-
-    Routines to handle common CardBus options
-
-======================================================================*/
-
-/* Default settings for PCI command configuration register */
-#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
-		  PCI_COMMAND_MASTER|PCI_COMMAND_WAIT)
-
-static void cb_get_state (socket_info_t * s)
-{
-	pci_readb (s, PCI_CACHE_LINE_SIZE, &s->cache);
-	pci_readb (s, PCI_LATENCY_TIMER, &s->pci_lat);
-	pci_readb (s, CB_LATENCY_TIMER, &s->cb_lat);
-	pci_readb (s, CB_CARDBUS_BUS, &s->cap.cardbus);
-	pci_readb (s, CB_SUBORD_BUS, &s->sub_bus);
-	pci_readw (s, CB_BRIDGE_CONTROL, &s->bcr);
-}
-
-static void cb_set_state (socket_info_t * s)
-{
-	pci_writel (s, CB_LEGACY_MODE_BASE, 0);
-	pci_writel (s, PCI_BASE_ADDRESS_0, s->cb_phys);
-	pci_writew (s, PCI_COMMAND, CMD_DFLT);
-	pci_writeb (s, PCI_CACHE_LINE_SIZE, s->cache);
-	pci_writeb (s, PCI_LATENCY_TIMER, s->pci_lat);
-	pci_writeb (s, CB_LATENCY_TIMER, s->cb_lat);
-	pci_writeb (s, CB_CARDBUS_BUS, s->cap.cardbus);
-	pci_writeb (s, CB_SUBORD_BUS, s->sub_bus);
-	pci_writew (s, CB_BRIDGE_CONTROL, s->bcr);
-}
-
-static void cb_set_opts (socket_info_t * s)
-{
-	if (s->cache == 0)
-		s->cache = 8;
-	if (s->pci_lat == 0)
-		s->pci_lat = 0xa8;
-	if (s->cb_lat == 0)
-		s->cb_lat = 0xb0;
-}
-
-/*======================================================================
-
-    Power control for Cardbus controllers: used both for 16-bit and
-    Cardbus cards.
-
-======================================================================*/
-
-static int cb_set_power (socket_info_t * s, socket_state_t * state)
-{
-	u_int reg = 0;
-
-	/* restart card voltage detection if it seems appropriate */
-	if ((state->Vcc == 0) && (state->Vpp == 0) &&
-	   !(cb_readl (s, CB_SOCKET_STATE) & CB_SS_VSENSE))
-		cb_writel (s, CB_SOCKET_FORCE, CB_SF_CVSTEST);
-	switch (state->Vcc) {
-	case 0:
-		reg = 0;
-		break;
-	case 33:
-		reg = CB_SC_VCC_3V;
-		break;
-	case 50:
-		reg = CB_SC_VCC_5V;
-		break;
-	default:
-		return -1;
-	}
-	switch (state->Vpp) {
-	case 0:
-		break;
-	case 33:
-		reg |= CB_SC_VPP_3V;
-		break;
-	case 50:
-		reg |= CB_SC_VPP_5V;
-		break;
-	case 120:
-		reg |= CB_SC_VPP_12V;
-		break;
-	default:
-		return -1;
-	}
-	if (reg != cb_readl (s, CB_SOCKET_CONTROL))
-		cb_writel (s, CB_SOCKET_CONTROL, reg);
-
-	return 0;
-}
-
-/*======================================================================
-
-    Generic routines to get and set controller options
-
-======================================================================*/
-
-static void get_bridge_state (socket_info_t * s)
-{
-	ti113x_get_state (s);
-	cb_get_state (s);
-}
-
-static void set_bridge_state (socket_info_t * s)
-{
-	cb_set_state (s);
-	i365_set (s, I365_GBLCTL, 0x00);
-	i365_set (s, I365_GENCTL, 0x00);
-	ti113x_set_state (s);
-}
-
-static void set_bridge_opts (socket_info_t * s)
-{
-	ti113x_set_opts (s);
-	cb_set_opts (s);
-}
-
-/*====================================================================*/
-#define PD67_EXT_INDEX		0x2e	/* Extension index */
-#define PD67_EXT_DATA		0x2f	/* Extension data */
-#define PD67_EXD_VS1(s)		(0x01 << ((s)<<1))
-
-#define pd67_ext_get(s, r) \
-    (i365_set(s, PD67_EXT_INDEX, r), i365_get(s, PD67_EXT_DATA))
-
-static int i365_get_status (socket_info_t * s, u_int * value)
-{
-	u_int status;
-
-	status = i365_get (s, I365_IDENT);
-	status = i365_get (s, I365_STATUS);
-	*value = ((status & I365_CS_DETECT) == I365_CS_DETECT) ? SS_DETECT : 0;
-	if (i365_get (s, I365_INTCTL) & I365_PC_IOCARD) {
-		*value |= (status & I365_CS_STSCHG) ? 0 : SS_STSCHG;
-	} else {
-		*value |= (status & I365_CS_BVD1) ? 0 : SS_BATDEAD;
-		*value |= (status & I365_CS_BVD2) ? 0 : SS_BATWARN;
-	}
-	*value |= (status & I365_CS_WRPROT) ? SS_WRPROT : 0;
-	*value |= (status & I365_CS_READY) ? SS_READY : 0;
-	*value |= (status & I365_CS_POWERON) ? SS_POWERON : 0;
-
-	status = cb_readl (s, CB_SOCKET_STATE);
-	*value |= (status & CB_SS_32BIT) ? SS_CARDBUS : 0;
-	*value |= (status & CB_SS_3VCARD) ? SS_3VCARD : 0;
-	*value |= (status & CB_SS_XVCARD) ? SS_XVCARD : 0;
-	*value |= (status & CB_SS_VSENSE) ? 0 : SS_PENDING;
-	/* For now, ignore cards with unsupported voltage keys */
-	if (*value & SS_XVCARD)
-		*value &= ~(SS_DETECT | SS_3VCARD | SS_XVCARD);
-
-	return 0;
-}	/* i365_get_status */
-
-static int i365_set_socket (socket_info_t * s, socket_state_t * state)
-{
-	u_char reg;
-
-	set_bridge_state (s);
-
-	/* IO card, RESET flag */
-	reg = 0;
-	reg |= (state->flags & SS_RESET) ? 0 : I365_PC_RESET;
-	reg |= (state->flags & SS_IOCARD) ? I365_PC_IOCARD : 0;
-	i365_set (s, I365_INTCTL, reg);
-
-	reg = I365_PWR_NORESET;
-	if (state->flags & SS_PWR_AUTO)
-		reg |= I365_PWR_AUTO;
-	if (state->flags & SS_OUTPUT_ENA)
-		reg |= I365_PWR_OUT;
-
-	cb_set_power (s, state);
-	reg |= i365_get (s, I365_POWER) & (I365_VCC_MASK | I365_VPP1_MASK);
-
-	if (reg != i365_get (s, I365_POWER))
-		i365_set (s, I365_POWER, reg);
-
-	return 0;
-}	/* i365_set_socket */
-
-/*====================================================================*/
-
-static int i365_set_mem_map (socket_info_t * s, struct pccard_mem_map *mem)
-{
-	u_short base, i;
-	u_char map;
-
-	debug ("i82365: SetMemMap(%d, %#2.2x, %d ns, %#5.5lx-%#5.5lx, %#5.5x)\n",
-		mem->map, mem->flags, mem->speed,
-		mem->sys_start, mem->sys_stop, mem->card_start);
-
-	map = mem->map;
-	if ((map > 4) ||
-	    (mem->card_start > 0x3ffffff) ||
-	    (mem->sys_start > mem->sys_stop) ||
-	    (mem->speed > 1000)) {
-		return -1;
-	}
-
-	/* Turn off the window before changing anything */
-	if (i365_get (s, I365_ADDRWIN) & I365_ENA_MEM (map))
-		i365_bclr (s, I365_ADDRWIN, I365_ENA_MEM (map));
-
-	/* Take care of high byte, for PCI controllers */
-	i365_set (s, CB_MEM_PAGE (map), mem->sys_start >> 24);
-
-	base = I365_MEM (map);
-	i = (mem->sys_start >> 12) & 0x0fff;
-	if (mem->flags & MAP_16BIT)
-		i |= I365_MEM_16BIT;
-	if (mem->flags & MAP_0WS)
-		i |= I365_MEM_0WS;
-	i365_set_pair (s, base + I365_W_START, i);
-
-	i = (mem->sys_stop >> 12) & 0x0fff;
-	switch (mem->speed / CYCLE_TIME) {
-	case 0:
-		break;
-	case 1:
-		i |= I365_MEM_WS0;
-		break;
-	case 2:
-		i |= I365_MEM_WS1;
-		break;
-	default:
-		i |= I365_MEM_WS1 | I365_MEM_WS0;
-		break;
-	}
-	i365_set_pair (s, base + I365_W_STOP, i);
-
-	i = ((mem->card_start - mem->sys_start) >> 12) & 0x3fff;
-	if (mem->flags & MAP_WRPROT)
-		i |= I365_MEM_WRPROT;
-	if (mem->flags & MAP_ATTRIB)
-		i |= I365_MEM_REG;
-	i365_set_pair (s, base + I365_W_OFF, i);
-
-	/* Turn on the window if necessary */
-	if (mem->flags & MAP_ACTIVE)
-		i365_bset (s, I365_ADDRWIN, I365_ENA_MEM (map));
-	return 0;
-}	/* i365_set_mem_map */
-
-static int i365_set_io_map (socket_info_t * s, struct pccard_io_map *io)
-{
-	u_char map, ioctl;
-
-	map = io->map;
-	/* comment out: comparison is always false due to limited range of data type */
-	if ((map > 1) || /* (io->start > 0xffff) || (io->stop > 0xffff) || */
-	    (io->stop < io->start))
-		return -1;
-	/* Turn off the window before changing anything */
-	if (i365_get (s, I365_ADDRWIN) & I365_ENA_IO (map))
-		i365_bclr (s, I365_ADDRWIN, I365_ENA_IO (map));
-	i365_set_pair (s, I365_IO (map) + I365_W_START, io->start);
-	i365_set_pair (s, I365_IO (map) + I365_W_STOP, io->stop);
-	ioctl = i365_get (s, I365_IOCTL) & ~I365_IOCTL_MASK (map);
-	if (io->speed)
-		ioctl |= I365_IOCTL_WAIT (map);
-	if (io->flags & MAP_0WS)
-		ioctl |= I365_IOCTL_0WS (map);
-	if (io->flags & MAP_16BIT)
-		ioctl |= I365_IOCTL_16BIT (map);
-	if (io->flags & MAP_AUTOSZ)
-		ioctl |= I365_IOCTL_IOCS16 (map);
-	i365_set (s, I365_IOCTL, ioctl);
-	/* Turn on the window if necessary */
-	if (io->flags & MAP_ACTIVE)
-		i365_bset (s, I365_ADDRWIN, I365_ENA_IO (map));
-	return 0;
-}	/* i365_set_io_map */
-
-/*====================================================================*/
-
-static int i82365_init (void)
-{
-	u_int val;
-	int i;
-
-	if ((socket.dev = pci_find_devices (supported, 0)) < 0) {
-		/* Controller not found */
-		return 1;
-	}
-	debug ("i82365 Device Found!\n");
-
-	pci_read_config_dword (socket.dev, PCI_BASE_ADDRESS_0, &socket.cb_phys);
-	socket.cb_phys &= ~0xf;
-
-	get_bridge_state (&socket);
-	set_bridge_opts (&socket);
-
-	i = i365_get_status (&socket, &val);
-
-	if (val & SS_DETECT) {
-		if (val & SS_3VCARD) {
-			state.Vcc = state.Vpp = 33;
-			puts (" 3.3V card found: ");
-		} else if (!(val & SS_XVCARD)) {
-			state.Vcc = state.Vpp = 50;
-			puts (" 5.0V card found: ");
-		} else {
-			puts ("i82365: unsupported voltage key\n");
-			state.Vcc = state.Vpp = 0;
-		}
-	} else {
-		/* No card inserted */
-		puts ("No card\n");
-		return 1;
-	}
-
-	state.flags = SS_IOCARD | SS_OUTPUT_ENA;
-	state.csc_mask = 0;
-	state.io_irq = 0;
-
-	i365_set_socket (&socket, &state);
-
-	for (i = 500; i; i--) {
-		if ((i365_get (&socket, I365_STATUS) & I365_CS_READY))
-			break;
-		udelay (1000);
-	}
-
-	if (i == 0) {
-		/* PC Card not ready for data transfer */
-		puts ("i82365 PC Card not ready for data transfer\n");
-		return 1;
-	}
-	debug (" PC Card ready for data transfer: ");
-
-	mem.map = 0;
-	mem.flags = MAP_ATTRIB | MAP_ACTIVE;
-	mem.speed = 300;
-	mem.sys_start = CONFIG_SYS_PCMCIA_MEM_ADDR;
-	mem.sys_stop = CONFIG_SYS_PCMCIA_MEM_ADDR + CONFIG_SYS_PCMCIA_MEM_SIZE - 1;
-	mem.card_start = 0;
-	i365_set_mem_map (&socket, &mem);
-
-	io.map = 0;
-	io.flags = MAP_AUTOSZ | MAP_ACTIVE;
-	io.speed = 0;
-	io.start = 0x0100;
-	io.stop = 0x010F;
-	i365_set_io_map (&socket, &io);
-
-#ifdef DEBUG
-	i82365_dump_regions (socket.dev);
-#endif
-
-	return 0;
-}
-
-static void i82365_exit (void)
-{
-	io.map = 0;
-	io.flags = 0;
-	io.speed = 0;
-	io.start = 0;
-	io.stop = 0x1;
-
-	i365_set_io_map (&socket, &io);
-
-	mem.map = 0;
-	mem.flags = 0;
-	mem.speed = 0;
-	mem.sys_start = 0;
-	mem.sys_stop = 0x1000;
-	mem.card_start = 0;
-
-	i365_set_mem_map (&socket, &mem);
-
-	socket.state.sysctl &= 0xFFFF00FF;
-
-	state.Vcc = state.Vpp = 0;
-
-	i365_set_socket (&socket, &state);
-}
-
-int pcmcia_on (void)
-{
-	u_int rc;
-
-	debug ("Enable PCMCIA " PCMCIA_SLOT_MSG "\n");
-
-	rc = i82365_init();
-	if (rc)
-		goto exit;
-
-	rc = check_ide_device(0);
-	if (rc == 0)
-		goto exit;
-
-	i82365_exit();
-
-exit:
-	return rc;
-}
-
-#if defined(CONFIG_CMD_PCMCIA)
-int pcmcia_off (void)
-{
-	printf ("Disable PCMCIA " PCMCIA_SLOT_MSG "\n");
-
-	i82365_exit();
-
-	return 0;
-}
-#endif
-
-/*======================================================================
-
-    Debug stuff
-
-======================================================================*/
-
-#ifdef DEBUG
-static void i82365_dump_regions (pci_dev_t dev)
-{
-	u_int tmp[2];
-	u_int *mem = (void *) socket.cb_phys;
-	u_char *cis = (void *) CONFIG_SYS_PCMCIA_MEM_ADDR;
-	u_char *ide = (void *) (CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_REG_OFFSET);
-
-	pci_read_config_dword (dev, 0x00, tmp + 0);
-	pci_read_config_dword (dev, 0x80, tmp + 1);
-
-	printf ("PCI CONF: %08X ... %08X\n",
-		tmp[0], tmp[1]);
-	printf ("PCI MEM:  ... %08X ... %08X\n",
-		mem[0x8 / 4], mem[0x800 / 4]);
-	printf ("CIS:      ...%c%c%c%c%c%c%c%c...\n",
-		cis[0x38], cis[0x3a], cis[0x3c], cis[0x3e],
-		cis[0x40], cis[0x42], cis[0x44], cis[0x48]);
-	printf ("CIS CONF: %02X %02X %02X ...\n",
-		cis[0x200], cis[0x202], cis[0x204]);
-	printf ("IDE:      %02X %02X %02X %02X %02X %02X %02X %02X\n",
-		ide[0], ide[1], ide[2], ide[3],
-		ide[4], ide[5], ide[6], ide[7]);
-}
-#endif	/* DEBUG */
-
-#endif /* CONFIG_I82365 */
diff --git a/configs/atc_defconfig b/configs/atc_defconfig
deleted file mode 100644
index 967be47..0000000
--- a/configs/atc_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC8260=y
-CONFIG_TARGET_ATC=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index c0d0cd9..5df0664 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@
 
 Board            Arch        CPU            Commit      Removed     Last known maintainer/contact
 =================================================================================================
+atc              powerpc     mpc8260        -           -           Wolfgang Denk <wd@denx.de>
 CPU86            powerpc     mpc8260        -           -           Wolfgang Denk <wd@denx.de>
 CPU87            powerpc     mpc8260        -           -
 ep82xxm          powerpc     mpc8260        -           -
diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile
index 43f8546..fdcbc00 100644
--- a/drivers/rtc/Makefile
+++ b/drivers/rtc/Makefile
@@ -11,7 +11,6 @@
 obj-$(CONFIG_RTC_BFIN) += bfin_rtc.o
 obj-y += date.o
 obj-$(CONFIG_RTC_DAVINCI) += davinci.o
-obj-$(CONFIG_RTC_DS12887) += ds12887.o
 obj-$(CONFIG_RTC_DS1302) += ds1302.o
 obj-$(CONFIG_RTC_DS1306) += ds1306.o
 obj-$(CONFIG_RTC_DS1307) += ds1307.o
diff --git a/drivers/rtc/ds12887.c b/drivers/rtc/ds12887.c
deleted file mode 100644
index d8a519b..0000000
--- a/drivers/rtc/ds12887.c
+++ /dev/null
@@ -1,217 +0,0 @@
-/*
- * (C) Copyright 2003
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * Date & Time support for the DS12887 RTC
- */
-
-#undef	RTC_DEBUG
-
-#include <common.h>
-#include <command.h>
-#include <config.h>
-#include <rtc.h>
-
-#if defined(CONFIG_CMD_DATE)
-
-#define RTC_SECONDS			0x00
-#define RTC_SECONDS_ALARM		0x01
-#define RTC_MINUTES			0x02
-#define RTC_MINUTES_ALARM		0x03
-#define RTC_HOURS			0x04
-#define RTC_HOURS_ALARM			0x05
-#define RTC_DAY_OF_WEEK			0x06
-#define RTC_DATE_OF_MONTH		0x07
-#define RTC_MONTH			0x08
-#define RTC_YEAR			0x09
-#define RTC_CONTROL_A			0x0A
-#define RTC_CONTROL_B			0x0B
-#define RTC_CONTROL_C			0x0C
-#define RTC_CONTROL_D			0x0D
-
-#define RTC_CA_UIP			0x80
-#define RTC_CB_DM			0x04
-#define RTC_CB_24_12			0x02
-#define RTC_CB_SET			0x80
-
-#if defined(CONFIG_ATC)
-
-static uchar rtc_read (uchar reg)
-{
-	uchar val;
-
-	*(volatile unsigned char*)(RTC_PORT_ADDR) = reg;
-	__asm__ __volatile__ ("sync");
-
-	val = *(volatile unsigned char*)(RTC_PORT_DATA);
-	return (val);
-}
-
-static void rtc_write (uchar reg, uchar val)
-{
-	*(volatile unsigned char*)(RTC_PORT_ADDR) = reg;
-	__asm__ __volatile__ ("sync");
-
-	*(volatile unsigned char*)(RTC_PORT_DATA) = val;
-	__asm__ __volatile__ ("sync");
-}
-
-#else
-# error Board specific rtc access functions should be supplied
-#endif
-
-int rtc_get (struct rtc_time *tmp)
-{
-	uchar sec, min, hour, mday, wday, mon, year;
-
-	/* check if rtc is available for access */
-	while( rtc_read(RTC_CONTROL_A) & RTC_CA_UIP)
-		;
-
-	sec  = rtc_read(RTC_SECONDS);
-	min  = rtc_read(RTC_MINUTES);
-	hour = rtc_read(RTC_HOURS);
-	mday = rtc_read(RTC_DATE_OF_MONTH);
-	wday = rtc_read(RTC_DAY_OF_WEEK);
-	mon  = rtc_read(RTC_MONTH);
-	year = rtc_read(RTC_YEAR);
-
-#ifdef RTC_DEBUG
-	printf( "Get RTC year: %d; mon: %d; mday: %d; wday: %d; "
-		"hr: %d; min: %d; sec: %d\n",
-		year, mon, mday, wday, hour, min, sec );
-
-	printf ( "Alarms: hour: %02x min: %02x sec: %02x\n",
-		 rtc_read (RTC_HOURS_ALARM),
-		 rtc_read (RTC_MINUTES_ALARM),
-		 rtc_read (RTC_SECONDS_ALARM) );
-#endif
-
-	if( !(rtc_read(RTC_CONTROL_B) & RTC_CB_DM))
-	{	    /* Information is in BCD format */
-printf(" Get: Convert BSD to BIN\n");
-		tmp->tm_sec  = bcd2bin (sec  & 0x7F);
-		tmp->tm_min  = bcd2bin (min  & 0x7F);
-		tmp->tm_hour = bcd2bin (hour & 0x3F);
-		tmp->tm_mday = bcd2bin (mday & 0x3F);
-		tmp->tm_mon  = bcd2bin (mon & 0x1F);
-		tmp->tm_year = bcd2bin (year);
-		tmp->tm_wday = bcd2bin (wday & 0x07);
-	}
-else
-	{
-		tmp->tm_sec  = sec  & 0x7F;
-		tmp->tm_min  = min  & 0x7F;
-		tmp->tm_hour = hour & 0x3F;
-		tmp->tm_mday = mday & 0x3F;
-		tmp->tm_mon  = mon & 0x1F;
-		tmp->tm_year = year;
-		tmp->tm_wday = wday & 0x07;
-	}
-
-
-	if(tmp->tm_year<70)
-		tmp->tm_year+=2000;
-	else
-		tmp->tm_year+=1900;
-
-	tmp->tm_yday = 0;
-	tmp->tm_isdst= 0;
-#ifdef RTC_DEBUG
-	printf ( "Get DATE: %4d-%02d-%02d (wday=%d)  TIME: %2d:%02d:%02d\n",
-		tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday,
-		tmp->tm_hour, tmp->tm_min, tmp->tm_sec);
-#endif
-
-	return 0;
-}
-
-int rtc_set (struct rtc_time *tmp)
-{
-	uchar save_ctrl_b;
-	uchar sec, min, hour, mday, wday, mon, year;
-
-#ifdef RTC_DEBUG
-	printf ( "Set DATE: %4d-%02d-%02d (wday=%d)  TIME: %2d:%02d:%02d\n",
-		tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday,
-		tmp->tm_hour, tmp->tm_min, tmp->tm_sec);
-#endif
-
-	if( !(rtc_read(RTC_CONTROL_B) & RTC_CB_DM))
-	{	    /* Information is in BCD format */
-		year = bin2bcd(tmp->tm_year % 100);
-		mon  = bin2bcd(tmp->tm_mon);
-		wday = bin2bcd(tmp->tm_wday);
-		mday = bin2bcd(tmp->tm_mday);
-		hour = bin2bcd(tmp->tm_hour);
-		min  = bin2bcd(tmp->tm_min);
-		sec  = bin2bcd(tmp->tm_sec);
-	}
-	else
-	{
-		year = tmp->tm_year % 100;
-		mon  = tmp->tm_mon;
-		wday = tmp->tm_wday;
-		mday = tmp->tm_mday;
-		hour = tmp->tm_hour;
-		min  = tmp->tm_min;
-		sec  = tmp->tm_sec;
-	}
-
-	/* disables the RTC to update the regs */
-	save_ctrl_b = rtc_read(RTC_CONTROL_B);
-	save_ctrl_b |= RTC_CB_SET;
-	rtc_write(RTC_CONTROL_B, save_ctrl_b);
-
-	rtc_write (RTC_YEAR, year);
-	rtc_write (RTC_MONTH, mon);
-	rtc_write (RTC_DAY_OF_WEEK, wday);
-	rtc_write (RTC_DATE_OF_MONTH, mday);
-	rtc_write (RTC_HOURS, hour);
-	rtc_write (RTC_MINUTES, min);
-	rtc_write (RTC_SECONDS, sec);
-
-	/* enables the RTC to update the regs */
-	save_ctrl_b &= ~RTC_CB_SET;
-	rtc_write(RTC_CONTROL_B, save_ctrl_b);
-
-	return 0;
-}
-
-void rtc_reset (void)
-{
-	struct rtc_time tmp;
-	uchar ctrl_rg;
-
-	ctrl_rg = RTC_CB_SET;
-	rtc_write(RTC_CONTROL_B,ctrl_rg);
-
-	tmp.tm_year = 1970 % 100;
-	tmp.tm_mon = 1;
-	tmp.tm_mday= 1;
-	tmp.tm_hour = 0;
-	tmp.tm_min = 0;
-	tmp.tm_sec = 0;
-
-#ifdef RTC_DEBUG
-	printf ( "RTC:   %4d-%02d-%02d %2d:%02d:%02d UTC\n",
-		    tmp.tm_year, tmp.tm_mon, tmp.tm_mday,
-		    tmp.tm_hour, tmp.tm_min, tmp.tm_sec);
-#endif
-
-	ctrl_rg = RTC_CB_SET | RTC_CB_24_12 | RTC_CB_DM;
-	rtc_write(RTC_CONTROL_B,ctrl_rg);
-	rtc_set(&tmp);
-
-	rtc_write(RTC_HOURS_ALARM, 0),
-	rtc_write(RTC_MINUTES_ALARM, 0),
-	rtc_write(RTC_SECONDS_ALARM, 0);
-
-	ctrl_rg = RTC_CB_24_12 | RTC_CB_DM;
-	rtc_write(RTC_CONTROL_B,ctrl_rg);
-}
-
-#endif
diff --git a/include/configs/atc.h b/include/configs/atc.h
deleted file mode 100644
index 77fa79a..0000000
--- a/include/configs/atc.h
+++ /dev/null
@@ -1,489 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_ATC		1	/* ...on a ATC board	*/
-#define CONFIG_CPM2		1	/* Has a CPM2 */
-
-#define	CONFIG_SYS_TEXT_BASE	0xFF000000
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere (for example, on the cogent platform, there are serial
- * ports on the motherboard which are used for the serial console - see
- * cogent/cma101/serial.[ch]).
- */
-#define  CONFIG_CONS_ON_SMC		/* define if console on SMC */
-#undef CONFIG_CONS_ON_SCC		/* define if console on SCC */
-#undef  CONFIG_CONS_NONE		/* define if console on something else*/
-#define CONFIG_CONS_INDEX	2	/* which serial channel for console */
-
-#define CONFIG_BAUDRATE		115200
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-#undef	CONFIG_ETHER_ON_SCC		/* define if ether on SCC       */
-#undef	CONFIG_ETHER_NONE		/* define if ether on something else */
-#define CONFIG_ETHER_ON_FCC
-
-#define CONFIG_ETHER_ON_FCC2
-
-/*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
- * - Enable Full Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK2	(CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
-# define CONFIG_SYS_CPMFCR_RAMTYPE	0
-# define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
-
-#define CONFIG_ETHER_ON_FCC3
-
-/*
- * - Rx-CLK is CLK15
- * - Tx-CLK is CLK16
- * - RAM for BD/Buffers is on the local Bus (see 28-13)
- * - Enable Half Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK3	(CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE3	(CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
-
-/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
-#define CONFIG_8260_CLKIN	64000000	/* in Hz */
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#undef	CONFIG_CLOCKS_IN_MHZ		/* clocks passsed to Linux in Hz */
-
-#define CONFIG_PREBOOT							\
-	"echo;"								\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;"\
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND						\
-	"bootp;"							\
-	"setenv bootargs root=/dev/nfs rw "				\
-	"nfsroot=${serverip}:${rootpath} "				\
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;"\
-	"bootm"
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configuration options
- */
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PCMCIA
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_IDE
-
-
-#define CONFIG_DOS_PARTITION
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END	0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address	*/
-
-#define CONFIG_SYS_PIO_MODE		0	/* IDE interface in PIO Mode 0	*/
-
-#define	CONFIG_SYS_RESET_ADDRESS 0xFFF00100	/* "bad" address		*/
-
-#define CONFIG_SYS_ALLOC_DPRAM
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define CONFIG_SPI
-
-#define CONFIG_RTC_DS12887
-
-#define RTC_BASE_ADDR		0xF5000000
-#define RTC_PORT_ADDR		RTC_BASE_ADDR + 0x800
-#define RTC_PORT_DATA		RTC_BASE_ADDR + 0x808
-
-#define CONFIG_MISC_INIT_R
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * Flash configuration
- */
-
-#define CONFIG_SYS_FLASH_BASE		0xFF000000
-#define CONFIG_SYS_FLASH_SIZE		0x00800000
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks      */
-#define CONFIG_SYS_MAX_FLASH_SECT	128	/* max num of sects on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
-
-#define CONFIG_FLASH_16BIT
-
-/*-----------------------------------------------------------------------
- * Hard Reset Configuration Words
- *
- * if you change bits in the HRCW, you must also change the CONFIG_SYS_*
- * defines for the various registers affected by the HRCW e.g. changing
- * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
- */
-#define CONFIG_SYS_HRCW_MASTER		(HRCW_CIP | HRCW_ISB100 | HRCW_BMS | \
-				 HRCW_BPS10 |\
-				 HRCW_APPC10)
-
-/* no slaves so just fill with zeros */
-#define CONFIG_SYS_HRCW_SLAVE1		0
-#define CONFIG_SYS_HRCW_SLAVE2		0
-#define CONFIG_SYS_HRCW_SLAVE3		0
-#define CONFIG_SYS_HRCW_SLAVE4		0
-#define CONFIG_SYS_HRCW_SLAVE5		0
-#define CONFIG_SYS_HRCW_SLAVE6		0
-#define CONFIG_SYS_HRCW_SLAVE7		0
-
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xF0000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE	0x2F00  /* Size of used area in DPRAM    */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- *
- * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE.
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_SDRAM_MAX_SIZE	0x08000000	/* max. 128 MB		*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()*/
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT
-#endif
-
-#define	CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define	CONFIG_PCI_PNP
-#define	CONFIG_SYS_PCI_MSTR_IO_BUS	0x00000000	/* PCI base   */
-
-#if 1
-/* environment is in Flash */
-#define CONFIG_ENV_IS_IN_FLASH	1
-# define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE+0x30000)
-# define CONFIG_ENV_SIZE		0x10000
-# define CONFIG_ENV_SECT_SIZE	0x10000
-#else
-#define CONFIG_ENV_IS_IN_EEPROM	1
-#define CONFIG_ENV_OFFSET		0
-#define CONFIG_ENV_SIZE		2048
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4	/* 16-byte page size	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE      32      /* For MPC8260 CPU              */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers                    2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-#define CONFIG_SYS_HID0_INIT   (HID0_ICE|HID0_DCE|HID0_ICFI|\
-			 HID0_DCI|HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID0_FINAL  (HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID2        0
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register                                     5-5
- *-----------------------------------------------------------------------
- * turn on Checkstop Reset Enable
- */
-#define CONFIG_SYS_RMR         RMR_CSRE
-
-/*-----------------------------------------------------------------------
- * BCR - Bus Configuration                                       4-25
- *-----------------------------------------------------------------------
- */
-#define BCR_APD01	0x10000000
-#define CONFIG_SYS_BCR		(BCR_APD01|BCR_ETM|BCR_LETM)	/* 8260 mode */
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration                             4-31
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SIUMCR      (SIUMCR_BBD|SIUMCR_APPC10|\
-			 SIUMCR_CS10PC00|SIUMCR_BCTLC10)
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control                             4-35
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR       (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
-			 SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
-#else
-#define CONFIG_SYS_SYPCR       (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
-			 SYPCR_SWRI|SYPCR_SWP)
-#endif /* CONFIG_WATCHDOG */
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control                     4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC     (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control                 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR       (PISCR_PS|PISCR_PTF|PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control                                   9-8
- *-----------------------------------------------------------------------
- * Ensure DFBRG is Divide by 16
- */
-#define CONFIG_SYS_SCCR        SCCR_DFBRG01
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration                         13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR        0
-
-#define CONFIG_SYS_MIN_AM_MASK	0xC0000000
-/*-----------------------------------------------------------------------
- * MPTPR - Memory Refresh Timer Prescaler Register              10-18
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_MPTPR       0x1F00
-
-/*-----------------------------------------------------------------------
- * PSRT - Refresh Timer Register                                10-16
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_PSRT        0x0f
-
-/*-----------------------------------------------------------------------
- * PSRT - SDRAM Mode Register                                   10-10
- *-----------------------------------------------------------------------
- */
-
-	/* SDRAM initialization values for 8-column chips
-	 */
-#define CONFIG_SYS_OR2_8COL	(CONFIG_SYS_MIN_AM_MASK		|\
-			 ORxS_BPD_4			|\
-			 ORxS_ROWST_PBI1_A7		|\
-			 ORxS_NUMR_12)
-
-#define CONFIG_SYS_PSDMR_8COL	(PSDMR_PBI			|\
-			 PSDMR_SDAM_A15_IS_A5		|\
-			 PSDMR_BSMA_A15_A17		|\
-			 PSDMR_SDA10_PBI1_A7		|\
-			 PSDMR_RFRC_7_CLK		|\
-			 PSDMR_PRETOACT_3W		|\
-			 PSDMR_ACTTORW_2W		|\
-			 PSDMR_LDOTOPRE_1C		|\
-			 PSDMR_WRC_1C			|\
-			 PSDMR_CL_2)
-
-	/* SDRAM initialization values for 9-column chips
-	 */
-#define CONFIG_SYS_OR2_9COL	(CONFIG_SYS_MIN_AM_MASK		|\
-			 ORxS_BPD_4			|\
-			 ORxS_ROWST_PBI1_A6		|\
-			 ORxS_NUMR_12)
-
-#define CONFIG_SYS_PSDMR_9COL	(PSDMR_PBI			|\
-			 PSDMR_SDAM_A16_IS_A5		|\
-			 PSDMR_BSMA_A15_A17		|\
-			 PSDMR_SDA10_PBI1_A6		|\
-			 PSDMR_RFRC_7_CLK		|\
-			 PSDMR_PRETOACT_3W		|\
-			 PSDMR_ACTTORW_2W		|\
-			 PSDMR_LDOTOPRE_1C		|\
-			 PSDMR_WRC_1C			|\
-			 PSDMR_CL_2)
-
-/*
- * Init Memory Controller:
- *
- * Bank Bus     Machine PortSz  Device
- * ---- ---     ------- ------  ------
- *  0   60x     GPCM    8  bit  Boot ROM
- *  1   60x     GPCM    64 bit  FLASH
- *  2   60x     SDRAM   64 bit  SDRAM
- *
- */
-
-#define CONFIG_SYS_MRS_OFFS	0x00000000
-
-/* Bank 0 - FLASH
- */
-#define CONFIG_SYS_BR0_PRELIM  ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK)  |\
-			 BRx_PS_16                      |\
-			 BRx_MS_GPCM_P                  |\
-			 BRx_V)
-
-#define CONFIG_SYS_OR0_PRELIM  (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE)     |\
-			 ORxG_CSNT                      |\
-			 ORxG_ACS_DIV1                  |\
-			 ORxG_SCY_3_CLK                 |\
-			 ORxU_EHTR_8IDLE)
-
-
-/* Bank 2 - 60x bus SDRAM
- */
-#ifndef CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_BR2_PRELIM  ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK)  |\
-			 BRx_PS_64                      |\
-			 BRx_MS_SDRAM_P                 |\
-			 BRx_V)
-
-#define CONFIG_SYS_OR2_PRELIM	 CONFIG_SYS_OR2_8COL
-
-#define CONFIG_SYS_PSDMR	 CONFIG_SYS_PSDMR_8COL
-#endif /* CONFIG_SYS_RAMBOOT */
-
-#define CONFIG_SYS_BR4_PRELIM  ((RTC_BASE_ADDR & BRx_BA_MSK)   |\
-			 BRx_PS_8                       |\
-			 BRx_MS_UPMA                    |\
-			 BRx_V)
-
-#define CONFIG_SYS_OR4_PRELIM  (ORxU_AM_MSK | ORxU_BI)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_I82365
-
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	0x81000000
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	0x1000
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card Adapter */
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
-#undef	CONFIG_IDE_LED			/* LED	 for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	0xa0000000
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	0x100
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	0x100
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x108
-
-#endif	/* __CONFIG_H */
diff --git a/include/pcmcia.h b/include/pcmcia.h
index 8e8831f..c8a730c 100644
--- a/include/pcmcia.h
+++ b/include/pcmcia.h
@@ -23,8 +23,6 @@
 
 #if defined(CONFIG_TQM8xxL)
 # define	CONFIG_PCMCIA_SLOT_B	/* The TQM8xxL use SLOT_B	*/
-#elif defined(CONFIG_ATC)		/* The ATC use SLOT_A	*/
-# define CONFIG_PCMCIA_SLOT_A
 #else
 # error "PCMCIA Slot not configured"
 #endif